Welcome to Koi Forum. Is this your first visit? Register
Page 3 of 3 FirstFirst 123
Results 41 to 51 of 51

Thread: DIY Smart Pond

  1. #41
    Senior Member Rank = Mature Champion RoyLittle0's Avatar
    Join Date
    Jun 2016
    Location
    Derby
    Posts
    2,303
    Thanks / Likes
    4177
    But at least now I know what buttons to press DIY Smart PondDIY Smart PondDIY Smart PondDIY Smart Pond


    Sent from my iPhone using Tapatalk
    4600 Gallon Concrete Block and Fiberglass
    2100 mm x 710 mm Infinity Window 32mm thick
    2 x Aerated Bottom Drains and Skimmer
    Filtreau HiFlow 30 Drum Filter
    Bio Chamber - 140 litres K1
    Bakki Shower - 30 KG Sakura Far Infrared Media
    2 x 18,000 lh pumps
    Idealseal MS290

    My Pond Build

  2. #42
    Extreme Koi Member Rank = Gosai NickK-UK's Avatar
    Join Date
    May 2015
    Posts
    312
    Thanks / Likes
    304
    Quote Originally Posted by RoyLittle0 View Post
    Lol that’s not my password, I’m not going to post that on here DIY Smart Pond this was the original software before modifying to to suite my application.

    It’s also protected by software and hardware firewalls and the ports are not accessible from outside of my automation VLAN, this isn’t even my house LAN
    Well when someone has a patch panel and Cisco rack mount hardware I suspected as much #woodenspoon


    Also this temperature sensor is really interesting as you can run multiple sensors off the same three wires, taking up one data pin on the controller as each sensor has it's own hard coded serial number onboard. Not sure on maximum bus distance compatibility but interesting none the less and there's probably waterproof version of this for submerging:

    https://create.arduino.cc/projecthub...arduino-9cc806

  3. #43
    Senior Member Rank = Mature Champion RoyLittle0's Avatar
    Join Date
    Jun 2016
    Location
    Derby
    Posts
    2,303
    Thanks / Likes
    4177
    Quote Originally Posted by NickK-UK View Post
    Well when someone has a patch panel and Cisco rack mount hardware I suspected as much #woodenspoon


    Also this temperature sensor is really interesting as you can run multiple sensors off the same three wires, taking up one data pin on the controller as each sensor has it's own hard coded serial number onboard. Not sure on maximum bus distance compatibility but interesting none the less and there's probably waterproof version of this for submerging:

    https://create.arduino.cc/projecthub...arduino-9cc806
    Iíll be testing the bus distance soon when I try to add another sensor in the greenhouse, so thatís going to add 6meters to the bus

    The sensors are waterproof, well the ones in my pond are


    Sent from my iPhone using Tapatalk
    4600 Gallon Concrete Block and Fiberglass
    2100 mm x 710 mm Infinity Window 32mm thick
    2 x Aerated Bottom Drains and Skimmer
    Filtreau HiFlow 30 Drum Filter
    Bio Chamber - 140 litres K1
    Bakki Shower - 30 KG Sakura Far Infrared Media
    2 x 18,000 lh pumps
    Idealseal MS290

    My Pond Build

  4. Thanks NickK-UK Thanked / Liked this Post
  5. #44
    Senior Member Rank = Mature Champion RoyLittle0's Avatar
    Join Date
    Jun 2016
    Location
    Derby
    Posts
    2,303
    Thanks / Likes
    4177
    I will at some point be installing Apache server and add the graphs to a web page, then get access remotely, but first I will add a feeding timer that works via time, daylight and temperature, so food is cut if the nightís draw in and increase with warmer water, obviously this will take some time, mainly on testing

    I also want to be able to turn the air on and off from the webpage, plus set timers etc, this does work through my phone but I want it all on one webpage


    Sent from my iPhone using Tapatalk
    4600 Gallon Concrete Block and Fiberglass
    2100 mm x 710 mm Infinity Window 32mm thick
    2 x Aerated Bottom Drains and Skimmer
    Filtreau HiFlow 30 Drum Filter
    Bio Chamber - 140 litres K1
    Bakki Shower - 30 KG Sakura Far Infrared Media
    2 x 18,000 lh pumps
    Idealseal MS290

    My Pond Build

  6. #45
    Senior Member Rank = Mature Champion RoyLittle0's Avatar
    Join Date
    Jun 2016
    Location
    Derby
    Posts
    2,303
    Thanks / Likes
    4177
    Well I found a little floor in my Temperature monitor, like all PC's, it goes to sleep after a period of time and stops recording, it took some figuring out what was happening as it just stopped responding, eventually I realised it was the PC going into sleep mode to save power, so I had to install a screensaver software and turn off hibernation from that, the little things that test us, anyway its now tracking data quite well, just need to get all the probes in position, especially the one at the bottom of the pond
    4600 Gallon Concrete Block and Fiberglass
    2100 mm x 710 mm Infinity Window 32mm thick
    2 x Aerated Bottom Drains and Skimmer
    Filtreau HiFlow 30 Drum Filter
    Bio Chamber - 140 litres K1
    Bakki Shower - 30 KG Sakura Far Infrared Media
    2 x 18,000 lh pumps
    Idealseal MS290

    My Pond Build

  7. #46
    Extreme Koi Member Rank = Gosai NickK-UK's Avatar
    Join Date
    May 2015
    Posts
    312
    Thanks / Likes
    304
    And automatic updates?

    For the Astro folks - windows update in the middle of the nigh photography run caused no end of problems!

    Iíll be interested in hearing how that goes.

  8. #47
    Senior Member Rank = Nanasai Mikeh83's Avatar
    Join Date
    Dec 2019
    Location
    Oxford
    Posts
    559
    Thanks / Likes
    1093
    Like your ideas here Roy DIY Smart Pond

    What probes are you using for the temperature?

    I would likely to have a play about, I have the coding experience but lack the hardware knowledge.


    Sent from my iPhone using Tapatalk

  9. #48
    Senior Member Rank = Mature Champion RoyLittle0's Avatar
    Join Date
    Jun 2016
    Location
    Derby
    Posts
    2,303
    Thanks / Likes
    4177
    I used the standard DS18B20 sensors, very cheap and on a 1-wire bus, so it only takes up one input on the Raspberry Pi

    https://www.amazon.co.uk/DS18b20-Wat...34248784&psc=1

    I need to find some more probes that will work for dissolved oxygen and I may also do a combined temperature and humidity for the ambient air

    I have the hardware experience just not a lot on coding
    4600 Gallon Concrete Block and Fiberglass
    2100 mm x 710 mm Infinity Window 32mm thick
    2 x Aerated Bottom Drains and Skimmer
    Filtreau HiFlow 30 Drum Filter
    Bio Chamber - 140 litres K1
    Bakki Shower - 30 KG Sakura Far Infrared Media
    2 x 18,000 lh pumps
    Idealseal MS290

    My Pond Build

  10. #49
    Senior Member Rank = Nanasai Mikeh83's Avatar
    Join Date
    Dec 2019
    Location
    Oxford
    Posts
    559
    Thanks / Likes
    1093
    Quote Originally Posted by RoyLittle0 View Post
    I used the standard DS18B20 sensors, very cheap and on a 1-wire bus, so it only takes up one input on the Raspberry Pi

    https://www.amazon.co.uk/DS18b20-Wat...34248784&psc=1

    I need to find some more probes that will work for dissolved oxygen and I may also do a combined temperature and humidity for the ambient air

    I have the hardware experience just not a lot on coding
    Thanks for sharing I will look into it.

    Most my coding experience is with sql, C# itís my day job. I find with coding itís mostly transferable just basic syntax variations.


    Sent from my iPhone using Tapatalk

  11. Thanks NickK-UK Thanked / Liked this Post
  12. #50
    Senior Member Rank = Mature Champion RoyLittle0's Avatar
    Join Date
    Jun 2016
    Location
    Derby
    Posts
    2,303
    Thanks / Likes
    4177
    Quote Originally Posted by Mikeh83 View Post
    Thanks for sharing I will look into it.

    Most my coding experience is with sql, C# it’s my day job. I find with coding it’s mostly transferable just basic syntax variations.
    Well if you can do sql then you have the database sorted, I did try using sql on my first attempt but due to work and it not working I gave up for some time and then when the influxdb route, its based on a project from circuits.dk but this was using Debian Stretch and I am using Debian Buster and nothing seemed to work properly so it had to be changed to suite the new version, but this shows you all the hardware connections as well

    https://www.circuits.dk/temperature-...-raspberry-pi/
    4600 Gallon Concrete Block and Fiberglass
    2100 mm x 710 mm Infinity Window 32mm thick
    2 x Aerated Bottom Drains and Skimmer
    Filtreau HiFlow 30 Drum Filter
    Bio Chamber - 140 litres K1
    Bakki Shower - 30 KG Sakura Far Infrared Media
    2 x 18,000 lh pumps
    Idealseal MS290

    My Pond Build

  13. #51
    Extreme Koi Member Rank = Gosai NickK-UK's Avatar
    Join Date
    May 2015
    Posts
    312
    Thanks / Likes
    304
    Quote Originally Posted by Mikeh83 View Post
    Thanks for sharing I will look into it.

    Most my coding experience is with sql, C# it’s my day job. I find with coding it’s mostly transferable just basic syntax variations.
    Cool

    I stopped professionally coding as as day job in 2005 - software engineering degree specialising in parallel and distributed computing. C/C++/SQL/Java mainly. I still do the odd bit of ASM/C/C++/Objective-C with GPU parallel image processing (mainly image alignment, image resolution and atmospheric deconvolution, along with FIR etc) and embedded stuff with Arduino/ODroid/PI. I've moved a little to using Octave (open source Matlab clone) as it allows you to focus on the maths and not worry too much about the processing (although octave itself is single threaded without recompiling MPI support!). Recently been playing with OpenFOAM to model the water flow in the pond.

    Back to the topic..

    I see that InfluxDB supports JWT authentication - that would be better than using a username/password.

 

 
Page 3 of 3 FirstFirst 123

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT +1. The time now is 01:08 AM. Online Koi Mag Forum
Powered by vBulletin® Version 4.2.3
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.

vBulletin Improved By vBFoster® (Lite Version), © UltimateScheme, Ltd.