Results 101 to 120 of 275
Thread: Quarantine/Hospital Tank.
-
12-01-2021, 10:55 AM #101
-
john1 Thanked / Liked this Post
-
12-01-2021, 10:59 AM #102
https://www.screwfix.com/p/schneider...4-x-89mm/900hv
Something like this but you need to measure the depth and some are expensive.John
-
Frimley Koi keeper Thanked / Liked this Post
-
12-01-2021, 11:02 AM #103
I've found with screwfix some things are cheaper and others aren't as it depends on supply and demand so the commonly sold stuff tends to be cheaper.
-
john1 Thanked / Liked this Post
-
12-01-2021, 11:29 AM #104
-
Frimley Koi keeper Thanked / Liked this Post
-
12-01-2021, 12:08 PM #105
I found with the bigger enclosures they were not stocked and had to be delivered.
I had a hard job trying to find smaller glands for the probe, picked them up of eBay in the end so have a pack of 10 now!
Think they close down to 1.5mm
Sent from my iPhone using Tapatalk
-
Frimley Koi keeper Thanked / Liked this Post
-
12-01-2021, 12:15 PM #106
If I find they don't clamp down enough and I've used the smallest gland then I use some insulation tape the same colour as the cable or gland depending on what I have at the time and then put a few turns of it round the cable so the gland clamps down nicely.
-
Wain Thanked / Liked this Post
-
12-01-2021, 12:20 PM #107
-
Frimley Koi keeper Thanked / Liked this Post
-
12-01-2021, 12:26 PM #108
-
12-01-2021, 12:56 PM #109
Just found this one and wondering if it might be a good choice.
Can't actually see the dimensions but being 8 way, I guess it would be large enough and with room for heat dissipation.
Check it out and let me know what you think, please. https://www.electricaldirect.co.uk/p...e-8-way-581062
-
Frimley Koi keeper Thanked / Liked this Post
-
12-01-2021, 04:33 PM #110
That may not be deep enough as the MCBs that normally get mounted into it stick out past the hole slightly and from memory the controller is deeper than an MCB is tall if that makes sense?
-
g mac Thanked / Liked this Post
-
12-01-2021, 05:52 PM #111
-
g mac Thanked / Liked this Post
-
12-01-2021, 05:55 PM #1121000 gal
2 x Hozelock 6000ltr 9W UV
Allpond Spin Filter 8000 11W UV
Blagdon pond oxy 640 ltr/hr
-
Frimley Koi keeper, g mac Thanked / Liked this Post
-
12-01-2021, 05:59 PM #113
-
Wain Thanked / Liked this Post
-
12-01-2021, 06:04 PM #114
-
12-01-2021, 06:19 PM #115
-
Frimley Koi keeper, Wain Thanked / Liked this Post
-
12-01-2021, 06:24 PM #116
-
12-01-2021, 11:57 PM #117
Sorry I got sidetracked with posting on various threads about Fred this evening and completely forgot to check on the enclosures for you Gary. I'll have a look tomorrow morning OK.
-
13-01-2021, 08:25 AM #118
-
Frimley Koi keeper Thanked / Liked this Post
-
13-01-2021, 11:30 AM #119
OK it's bloody cold in this garage right now
These are the 2 I have
IMO EN15C this one is 125mm x 175mm x 100mm
IMO EN17C this one is 175mm x 175mm x 100mm
Both are IP66 with DIN rails that if required can be mounted inside the enclosure for extra connections but you'll need to get some DIN rail connectors or just use WAGOs or connector strip.
These probably aren't the cheapest ones but will at least give you the sizes you need.
The smaller one will do fine if you are just going for a heater control set up but I got the bigger one for the auto feeder system I described in the PM.
Any questions feel free to ask OK.
Good luck
-
13-01-2021, 11:39 AM #120
I'm pretty sure they are the right boxes but just double check with John that the 100mm depths are deep enough. I can't find the controllers at the moment.
Aquaforte Dm vario 20000 pumps
Still for sale. Postage available for cost Sent from my SM-S901B using Tapatalk