" koiforum.uk - The home of Extreme Koi "
Ianb
Extreme Koi Member
Find latest posts
View Articles
View Blog EntriesMini Statistics
- Join Date
- 07-09-2013
- Last Activity
- 11-08-2020 03:34 PM
- Blog Entries
- 0
- Avatar
- Tab Content
- Ianb's Activity
- About Me
- Post Thanks / Like
-
Older Activity
-
05-08-2020, 09:58 PMHave a look at the evolve showers, they are a bit cheaper direct, some on eBay, depends if you want plastic or stainless steel4 replies | 96 view(s) -
05-08-2020, 07:01 PMNexus has been running at higher rate for a couple of days now, did filter maintenance today, when I opened the gate valve to fill the eazy there was...10 replies | 215 view(s)
-
04-08-2020, 10:04 AMI have ran mine at a lower limit approx 4000L and it would not pull the larger solids through the last 90deg bend, this was obvious to me because as...10 replies | 215 view(s)
-
03-08-2020, 08:32 PMDecided to put 25L of K1 micro in easy, about 50/50 split K1 micro and beads in Econobead. That in total 25L. K1 micro plus 100L K1 in bio of nexus....10 replies | 215 view(s)
-
03-08-2020, 09:16 AMThanks, I have doubled my flow rate from about 4000 L/P/H To 8000 approx, problem was that The nexus wasn’t pulling all the solids through the bottom...10 replies | 215 view(s)
-
02-08-2020, 11:03 AMI know the nexus 200/210/220 have a maximum flow rate of 10000 L/P/H but I have an underwater return which makes the output difficult to measure. Any...10 replies | 215 view(s)
-
27-07-2020, 05:51 PMThanks, a standard 1.5 inch pressure ball valve sorted it out, not going to use it for a week as it’s a new addition to my filter system Ian7 replies | 83 view(s)
-
27-07-2020, 10:47 AMThanks, I think I will have to cut just above the none return valve or I will have to strip the bypass, as this is white it leads me to question is...7 replies | 83 view(s)
-
26-07-2020, 11:35 PMThanks that’s reassuring, it’s a bit confusing I have seen some videos on utube where people have a bypass with no ball valve and some have needed to...7 replies | 83 view(s)
-
26-07-2020, 09:03 PMJust made a novice mistake. Fitted a bypass to my eb60, water came through the blower that wasn’t switched on. Will fit a ball valve but haven’t seen...7 replies | 83 view(s)
About Ianb
Basic Information
About Ianb
- Location:
- Lancashire
Statistics
Total Posts
- Total Posts
- 357
- Posts Per Day
- 0.14
- Last Post
- Looking for bakki shower 05-08-2020 09:58 PM
General Information
- Last Activity
- 11-08-2020 03:34 PM
- Join Date
- 07-09-2013
- Referrals
- 0
06-08-2020
- 06:48 AM - freddyboy clicked Thanks for this post: Nexus flow rates by IanbNexus has been running...
05-08-2020
- 06:28 AM - freddyboy clicked Thanks for this post: Koi to move on by IanbYou could always tell...
04-08-2020
- 10:50 PM - Gray clicked Thanks for this post: Koi to move on by IanbBronze Ghost reserved....
- 06:11 AM - freddyboy clicked Thanks for this post: Nexus flow rates by IanbDecided to put 25L of K1...
-
Whos Online
-
Sponsor
-
Forum Statistics
-
New Forum Posts
-
-
Latest Forum Threads
-
Draco Drum Solum 16 + Standard Bio...
@blondie you may want to use MPDE water pipe and connectors rather than copper pipe and garden hose...