Results 1 to 10 of 10
-
24-04-2020, 05:54 AM #1
Evolution aqua uv 110w ballast wiring diagram needed
Hi guys wondering if anyone knows how the ballast is wired on the ea 110w as I stupidly removed the old ballast without marking which wire goes where and I'm totally buggered. Hope you guys can help
Help will be very much appreciated
Thanks
Sent from my SM-G960F using Tapatalk
-
24-04-2020, 07:55 AM #24600 Gallon Concrete Block and Fiberglass
2100 mm x 710 mm Infinity Window 32mm thick glass
2 x Aerated Bottom Drains and Skimmer
Filtreau HiFlow 30 Drum Filter
Bio Chamber - 140 litres K1
Bakki Shower - 30 KG Sakura Far Infrared Media
2 x 18,000 lh pumps
Heated from house boiler through a heat exchanger
Idealseal MS290
My Pond Build
-
Gazkoi Thanked / Liked this Post
-
24-04-2020, 06:27 PM #3
-
freddyboy Thanked / Liked this Post
-
24-04-2020, 08:55 PM #4
Ok here we go
That ballast is for two tubes, each tube has two connections at each end, the connections on the end are not critical provided they go to the correct end it doesn't matter which terminal on the end cap is which
Tube 1 - End 1 (Bottom lamp in the picture)
Connect to terminal 27 on the ballast
Connect to terminal 26 on the ballast
Tube 1 - End 2 (Bottom lamp in the picture)
Connect to terminal 23 on the ballast
Connect to terminal 21 on the ballast but also links to Tube 2 - End 2
Tube 2 - End 1 (Top lamp in the picture)
Connect to terminal 24 on the ballast
Connect to terminal 25 on the ballast
Tube 2 - End 2 (Top lamp in the picture)
Connect to terminal 22 on the ballast
Connect from link from Tube 1 - End 2
Hope this helps4600 Gallon Concrete Block and Fiberglass
2100 mm x 710 mm Infinity Window 32mm thick glass
2 x Aerated Bottom Drains and Skimmer
Filtreau HiFlow 30 Drum Filter
Bio Chamber - 140 litres K1
Bakki Shower - 30 KG Sakura Far Infrared Media
2 x 18,000 lh pumps
Heated from house boiler through a heat exchanger
Idealseal MS290
My Pond Build
-
24-04-2020, 08:56 PM #5
1 = Live (Brown)
2 = Earth (Green/Yellow)
3 = Neutral (Blue)4600 Gallon Concrete Block and Fiberglass
2100 mm x 710 mm Infinity Window 32mm thick glass
2 x Aerated Bottom Drains and Skimmer
Filtreau HiFlow 30 Drum Filter
Bio Chamber - 140 litres K1
Bakki Shower - 30 KG Sakura Far Infrared Media
2 x 18,000 lh pumps
Heated from house boiler through a heat exchanger
Idealseal MS290
My Pond Build
-
freddyboy Thanked / Liked this Post
-
24-04-2020, 10:26 PM #6
-
freddyboy Thanked / Liked this Post
-
24-04-2020, 11:48 PM #74600 Gallon Concrete Block and Fiberglass
2100 mm x 710 mm Infinity Window 32mm thick glass
2 x Aerated Bottom Drains and Skimmer
Filtreau HiFlow 30 Drum Filter
Bio Chamber - 140 litres K1
Bakki Shower - 30 KG Sakura Far Infrared Media
2 x 18,000 lh pumps
Heated from house boiler through a heat exchanger
Idealseal MS290
My Pond Build
-
freddyboy Thanked / Liked this Post
-
25-04-2020, 12:37 AM #8
Ok with light tester it flashes that there voltage there but with a volt meter it shows 0. Even when I run the light tester around the bulb connectors it flashes saying theres voltage there. Would you know what blows on the ballast ?
Thanks again
Sent from my SM-G960F using Tapatalk
-
freddyboy Thanked / Liked this Post
-
25-04-2020, 08:31 AM #9
Old style ballasts which are basically a big coil of wire and you can smell then when they have gone, these usually require a starter across the tubes
The one you have I think is electronic and it could be anything inside it that can blow, they are throw away units
Why did you remove the old ballast and is this a new one, it doesn't look very new
I think you should get a reading from your tester, set to AC
Terminals 1 and 3 = 230 to 245 volts
Terminals 21 and 22 = 380 volts + or - 10% (this may pulse as it needs to start the tube, so may give a strange reading if the tubes are not lit)4600 Gallon Concrete Block and Fiberglass
2100 mm x 710 mm Infinity Window 32mm thick glass
2 x Aerated Bottom Drains and Skimmer
Filtreau HiFlow 30 Drum Filter
Bio Chamber - 140 litres K1
Bakki Shower - 30 KG Sakura Far Infrared Media
2 x 18,000 lh pumps
Heated from house boiler through a heat exchanger
Idealseal MS290
My Pond Build
-
freddyboy Thanked / Liked this Post
-
25-04-2020, 08:34 AM #10
This one should do the trick, but if you search for the part number you can get the exact one
https://www.bltdirect.com/osram-55-w...xoC7HgQAvD_BwE4600 Gallon Concrete Block and Fiberglass
2100 mm x 710 mm Infinity Window 32mm thick glass
2 x Aerated Bottom Drains and Skimmer
Filtreau HiFlow 30 Drum Filter
Bio Chamber - 140 litres K1
Bakki Shower - 30 KG Sakura Far Infrared Media
2 x 18,000 lh pumps
Heated from house boiler through a heat exchanger
Idealseal MS290
My Pond Build
-
freddyboy Thanked / Liked this Post
The Daily pond temp thread
Pond still covered, currently 11.6C Been really mild this year as far as pond temps go. ...