Results 1 to 15 of 15
Thread: Nexus 220 help please
-
21-01-2020, 11:13 PM #1
Nexus 220 help please
I want to covert the nexus to pump feed , it is gravity fed , the black pipe which is taken out to convert to gravity, is now missing, I need it to convert back ,could anyone tell me the length of the pipe , that goes back in the inlet , thanks in anticipation
regards Chris
-
freddyboy Thanked / Liked this Post
-
21-01-2020, 11:20 PM #2
Confused, unless I’m reading it wrong, the pipe is fitted for Gravity Fed, pump fed the pipe is removed. Either way the pipe needs to protrude about 15mm for pump fed.
https://evolutionaqua.com/pub/media/...Kit-Manual.pdf
-
freddyboy Thanked / Liked this Post
-
21-01-2020, 11:38 PM #3
When you buy the 220 it is set up for pump feed , to convert it to gravity feed , you need to remove boot on inlet , remove screws and then a long black pipe is taken out , so you can use it for gravity feed , I want to put the pipe back , so it is set up for pump feed again , trouble is pipe is missing so I need the size of it especially the length. Hope that makes sense
kind regards Chris
-
freddyboy Thanked / Liked this Post
-
22-01-2020, 12:20 AM #4
Hi mate I brought a second hand nexus and needed some parts I called in at aquatics near me and the ops guy on there there was extremely helpful , and got the parts in store that I needed . One part being the piece your in about . I can’t remember the size of it now but he’ll know and me more than happy to help I’m sure
-
22-01-2020, 12:21 AM #5
give him a call
Sent from my iPhone using Tapatalk
-
22-01-2020, 06:58 AM #6
Im sure there is a measurement on the EA website.I converted my pals from gravity to pump fed..amd im sure thats where i got the info.If he still had it i would measure it for you
-
freddyboy Thanked / Liked this Post
-
22-01-2020, 09:54 AM #7
Thanks would really help look on website,can’t find anything
regards Chris
-
freddyboy Thanked / Liked this Post
-
22-01-2020, 10:05 AM #8
Just found the answer for pipe 40.5 cm long inch
pipe thanks to all those who replied
-
22-01-2020, 11:53 AM #9
Where abouts are you cj ???
Sent from my iPhone using Tapatalk
-
freddyboy Thanked / Liked this Post
-
22-01-2020, 01:40 PM #10
I live in Kent
-
freddyboy Thanked / Liked this Post
-
22-01-2020, 02:04 PM #11
Hi , i had the same on my 210 when i got it just normal 4" pipe and mine stops just about 1" below the over flow pipe . hope that helps
-
freddyboy Thanked / Liked this Post
-
22-01-2020, 02:31 PM #12
Ahh shame I’ve got all sorts of bits of pipe in the shed ..
and I work on site so can always pick up all sorts of pipe etc etc I’d of give you some
Sent from my iPhone using Tapatalk
-
22-01-2020, 03:39 PM #13
Thanks all sorted
-
23-01-2020, 12:36 AM #14
Only just seen this thread.... Have one of these pipes sitting in the garage. Not sure if I'd part with it permanently but happy to lend it / measure it photograph it etc if info or the pipe itself is still needed.
-
-
23-01-2020, 01:10 AM #15
Thanks think I have it sorted , if not will contact you , thanks anyway
regards Chris
The Daily pond temp thread
Pond still covered, currently 11.6C Been really mild this year as far as pond temps go. ...