Results 1 to 15 of 15
Thread: Queni drum problem
-
08-12-2018, 07:32 PM #1
Queni drum problem
Anyone help I seem to be getting water coming from control box that’s above outlets on my queni drum it only happens when it cleans once it’s finished the cleaning cycle water stops it’s coming from behind where the panel screws onto box on front it flows out of seam where the panel screws onto the box the box on front of drum shown in pictureIMG]https://uploads.tapatalk-cdn.com/20181208/54570821b3eec31c3af4b938503e4c35.jpg[/IMG]
-
08-12-2018, 07:59 PM #2
Queni drum problem
54DA53D6-EA6F-46D5-AC1F-AF333D1EB5FD-2844-000001A9BF97E07A.jpg
This picture works it’s the box with screws in it on front where waters coming from
Sent from my iPhone using Tapatalk
-
Skoosh88 Thanked / Liked this Post
-
09-12-2018, 01:21 AM #3
-
09-12-2018, 08:42 AM #4
Dont have a Queni drum but if you have 240 electrics in there it wont be doing any good,or any elecs in fact.
There must be wires going into the back so can you not seal them with a good silicon which should do the trick,from the wet side i mean.John
-
Skoosh88 Thanked / Liked this Post
-
09-12-2018, 11:06 AM #5
I think what’s happening I will inspect a bit more but my thoughts were when it cleans water from jets hit drum surface and it lifts lid slightly runs onto and down box on drum I’ve had front off this box and there’s no way I can see water can get in there could be wrong or I’m not looking properly which knowing me could be the case
Sent from my iPhone using Tapatalk
-
09-12-2018, 11:27 AM #6
Shouldnt really leak from the lid but if it does a bit of silicone on the edge of the cover would help.
Sorry i cant help any more as i havnt got one but someone with a queni drum should be able to help.John
-
09-12-2018, 11:34 AM #7
mine doesnt
-
10-12-2018, 11:50 AM #8
IMG_0133.jpgIMG_0133.jpg
You can see on pic the water dripping from bottom of box on front of drum
Sent from my iPhone using Tapatalk
-
10-12-2018, 11:53 AM #9
have you taken the cover off to have a look ? where is the water coming in from ? if so is it a case of just using a sealent ?
-
10-12-2018, 11:57 AM #10
Yeh but as yet can’t see nothing been in touch with mike at queni koi he his really good cant fault there after sales and knowledge about the drum he may come up with a solution to it
-
10-12-2018, 03:52 PM #11
[QUOTE=davec;283170]I think what’s happening I will inspect a bit more but my thoughts were when it cleans water from jets hit drum surface and it lifts lid slightly runs onto and down box on drum I’ve had front off this box and there’s no way I can see water can get in there could be wrong or I’m not looking properly which knowing me could be the case
on my kc10 drum it has a removeable cover over the spray bars to stop this,anything you can do like it,andi
-
16-12-2018, 10:05 PM #12
Did you get to the bottom of this Dave?
Sent from my iPhone using Tapatalk
-
16-12-2018, 10:09 PM #13
No not yet it ain’t happened again touch wood does yours still do it what was causing yours to do it
-
16-12-2018, 10:11 PM #14
I haven’t noticed it doing it again, I’m sure I had the lid off when it happened and the more I think about it I reckon it was just water that had run down the side and around underneath. The control box seems pretty watertight
Sent from my iPhone using Tapatalk
-
16-12-2018, 10:13 PM #15
Yeh I think that’s what happened with mine
The Daily pond temp thread
Pond still covered, currently 11.6C Been really mild this year as far as pond temps go. ...